
Cyrus Streamline series User Instructions
12
Select the Setup option from the Main Menu.•
The Setup Menu is displayed.
Select the n-remote option from the Setup Menu.•
The Start Pairing option will be highlighted. Move on to the next step
before selecting this option.
On the n-remote, press the • (settings) button.
The System-Settings menu will be displayed.
Getting started with the n-remote
Charging the remote control
The remote control must be fully charged for at least 2 hours before first
use.
Place the dock in a convenient and stable position.•
Connect the mini-USB cable from the Charger to the socket on the •
charging dock.
Connect the charger unit to the mains.•
Place the remote control on the dock.•
The battery level indicator on the display will show the current level and
the charge indicator (arrow) when charging.
System-Settings
User-Settings
Device Selection
Change Zone
System Information
Start Pairing
Stream CyIR
12:30 Not connected
Pairing should occur almost immediately. The Streamline will return to
the Source Menu and the n-remote will prompt for a device name.
Charging from mini-USB
The n-remote may also be charged from the mini-USB cable connected
directly to the charger, or to a computer.
Connect the mini-USB plug directly to the USB socket on the bottom of
the remote control.
To pair an n-remote to a Streamline
The wireless system of each n-remote must be paired to a particular
Streamline. In this way, neighbouring Streamline units can operate
without risk of interference.
Pairing should only be necessary once during initial setup unless the
n-remote or Streamline are later to be paired with another unit.
When pairing a Streamline to an n-remote, it is necessary for both
components to be in close range.
Press and hold the • key on the front panel to return to the Main
Menu.
V+/V-/Mute to
Don’t change
CyIR
Line 1
12:30 Not connected
Stream
CyIR
Stream
NOTE: This setting can be changed at any time via the ‘Key mapping’
option of the ‘User-settings’ menu.
Once this setting has been made, pairing is complete.
Unpairing a remote control
If necessary, you can unpair n-remotes from a Streamline.
For more information about unpairing n-remotes, refer to the Setup menu
section of the Streamline instructions.
Charge indicator
Pairing success
Please enter name:
Stream
Line 1
12:30 Not connected
CyIR
You will now get the option to select how the n-remote volume control
will operate.
Press ENTER to select the default •
name ‘Stream’ (recommended)
or rename this device.
Choose ‘Don’t change’ to retain •
the volume setup used when the
n-remote was previously paired
to the Streamline.
Choose ‘Stream’ if you have •
connected speakers to the
Streamline or if you are using the
Streamline as a preamplifier.
The n-remote volume buttons will
now control the Streamline volume
setting.
Choose ‘CyIR’ if you have •
connected the Streamline as an
input to a Cyrus stereo amplifier.
The n-remote volume buttons will
now operate the volume control of a
Cyrus stereo amplifier (via infra-red).
You will now get the option to assign the Streamline device to one of the
four quick-access Hotkeys below the display..
Choose Hotkey
None
Change Zone
Line 1
12:30 Not connected
CyIR
Hotkey A
Hotkey B
Hotkey C
Hotkey D
CyIr
A B C D
If you select one of the Hotkeys A •
to D, the ‘Stream’ device will be
selectable by the chosen Hotkey.
In the example on the left, •
Hotkey B is pre-assigned to
the CyIr device (to send remote
control commands to other
Cyrus products), so Hotkey A
would be recommended for the
Streamline.
Highlight the ‘Start Pairing’ •
option.
To begin pairing, select the ‘Start •
Pairing’ options on both the
n-remote and Streamline within
one or two seconds.
Komentarze do niniejszej Instrukcji